This is a continuation of a long topic, addressed by post number rather than by page. Start at post 1.
Worth separating two things that post #117 runs together.
Needle gauge: smaller numbers (30G) are finer and less painful. Larger numbers (25G) are courser. For subcutaneous injection, 27-30G is typical. Finer needles take longer to draw up but hurt less.
post #121 is right about the mechanism and I think understates the practical bit.
Dead volume: residual liquid in the hub and needle after withdrawal. Typical residual is 0.01 to 0.02 mL for an insulin syringe with a fixed needle. Accounting for it matters if precision matters.
Syringe barrel size: common sizes are 0.3 mL, 0.5 mL, and 1.0 mL. Smaller barrels are more legible for small doses. Larger barrels hold larger volumes. Choose based on your dose.
For anyone arriving from a search: the marked solution above is the direct answer, and the replies underneath it add the caveats that make it safe to use.
On post #121 — agreed on the reasoning, with one qualification.
Sharps disposal: needles and syringes should be disposed in a sharps container (a rigid, puncture-resistant container). Do not put them in regular trash. Many pharmacies accept filled sharps containers.
post #125 answers the question as asked. The question underneath it is different.
Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.
Fixed versus detachable needles: insulin syringes usually have fixed needles (no dead volume loss to the hub). Luer-lock syringes use detachable needles (more dead volume). Fixed needles are preferred for small doses.
Needle length: typical lengths for subcutaneous injection are 4-6 mm (short), 8 mm (standard), or 10-12 mm (longer). Longer needles are needed for deeper tissue or if you have abdominal adiposity.
post #129 is right about the mechanism and I think understates the practical bit.
I disagree with the reply above, and I think the disagreement is substantive rather than terminological.
The distinction being drawn does not survive when you look at the published data for this specific question. I would be glad to be shown wrong on this, because the version I am arguing against is more convenient.
Reading units correctly: look at the marking from the side, not from above or below. The bottom of the plunger tip is the reading. Parallax error (wrong angle) is a source of dosing error.
I read post #130 twice before replying, because I had assumed the opposite.
Insulin syringe graduations: U-100 syringes are marked in units where 100 units = 1 mL. Always confirm your syringe is U-100. Confusion between insulin units and milligrams is the most common syringe error.
Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.
Sharps disposal: needles and syringes should be disposed in a sharps container (a rigid, puncture-resistant container). Do not put them in regular trash. Many pharmacies accept filled sharps containers.
Syringe barrel size: common sizes are 0.3 mL, 0.5 mL, and 1.0 mL. Smaller barrels are more legible for small doses. Larger barrels hold larger volumes. Choose based on your dose.
Coming back to post #134, because the follow-up matters more than the original answer.
Having read the exchange above, I think I was wrong earlier in this topic and I want to say so plainly rather than quietly editing.
The correction was fair and I had been repeating something I had not checked carefully enough.
post #136 answers the question as asked. The question underneath it is different.
Needle gauge: smaller numbers (30G) are finer and less painful. Larger numbers (25G) are courser. For subcutaneous injection, 27-30G is typical. Finer needles take longer to draw up but hurt less.
Needle length: typical lengths for subcutaneous injection are 4-6 mm (short), 8 mm (standard), or 10-12 mm (longer). Longer needles are needed for deeper tissue or if you have abdominal adiposity.
This follows post #136 rather than contradicting it.
Fixed versus detachable needles: insulin syringes usually have fixed needles (no dead volume loss to the hub). Luer-lock syringes use detachable needles (more dead volume). Fixed needles are preferred for small doses.
Insulin syringe graduations: U-100 syringes are marked in units where 100 units = 1 mL. Always confirm your syringe is U-100. Confusion between insulin units and milligrams is the most common syringe error.
Picking up post #139: that is the part I would want checked first.
Dead volume: residual liquid in the hub and needle after withdrawal. Typical residual is 0.01 to 0.02 mL for an insulin syringe with a fixed needle. Accounting for it matters if precision matters.
On post #139 — agreed on the reasoning, with one qualification.
Fixed versus detachable needles: insulin syringes usually have fixed needles (no dead volume loss to the hub). Luer-lock syringes use detachable needles (more dead volume). Fixed needles are preferred for small doses.
Sharps disposal: needles and syringes should be disposed in a sharps container (a rigid, puncture-resistant container). Do not put them in regular trash. Many pharmacies accept filled sharps containers.
Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.
Worth separating two things that post #143 runs together.
Syringe barrel size: common sizes are 0.3 mL, 0.5 mL, and 1.0 mL. Smaller barrels are more legible for small doses. Larger barrels hold larger volumes. Choose based on your dose.
For anyone arriving from a search: the marked solution above is the direct answer, and the replies underneath it add the caveats that make it safe to use.
Dead volume: residual liquid in the hub and needle after withdrawal. Typical residual is 0.01 to 0.02 mL for an insulin syringe with a fixed needle. Accounting for it matters if precision matters.