A ten-fold dose error caught before injection — one year on posts 61–90

Syringe barrel size: common sizes are 0.3 mL, 0.5 mL, and 1.0 mL. Smaller barrels are more legible for small doses. Larger barrels hold larger volumes. Choose based on your dose.

For anyone arriving from a search: the marked solution above is the direct answer, and the replies underneath it add the caveats that make it safe to use.

Worth separating two things that post #73 runs together.

Insulin syringe graduations: U-100 syringes are marked in units where 100 units = 1 mL. Always confirm your syringe is U-100. Confusion between insulin units and milligrams is the most common syringe error.

Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.

Needle length: typical lengths for subcutaneous injection are 4-6 mm (short), 8 mm (standard), or 10-12 mm (longer). Longer needles are needed for deeper tissue or if you have abdominal adiposity.

Picking up post #77: that is the part I would want checked first.

Needle gauge: smaller numbers (30G) are finer and less painful. Larger numbers (25G) are courser. For subcutaneous injection, 27-30G is typical. Finer needles take longer to draw up but hurt less.

This follows post #78 rather than contradicting it.

Fixed versus detachable needles: insulin syringes usually have fixed needles (no dead volume loss to the hub). Luer-lock syringes use detachable needles (more dead volume). Fixed needles are preferred for small doses.

I read post #80 twice before replying, because I had assumed the opposite.

Practical note that does not fit anywhere else. Whatever you conclude from this topic, write down what you did and when. The single most useful thing in your own records is not any individual result; it is that they are dated and consecutive.

Syringe barrel size: common sizes are 0.3 mL, 0.5 mL, and 1.0 mL. Smaller barrels are more legible for small doses. Larger barrels hold larger volumes. Choose based on your dose.

Dead volume: residual liquid in the hub and needle after withdrawal. Typical residual is 0.01 to 0.02 mL for an insulin syringe with a fixed needle. Accounting for it matters if precision matters.

I disagree with the reply above, and I think the disagreement is substantive rather than terminological.

The distinction being drawn does not survive when you look at the published data for this specific question. I would be glad to be shown wrong on this, because the version I am arguing against is more convenient.

Coming back to post #84, because the follow-up matters more than the original answer.

Sharps disposal: needles and syringes should be disposed in a sharps container (a rigid, puncture-resistant container). Do not put them in regular trash. Many pharmacies accept filled sharps containers.

post #86 answers the question as asked. The question underneath it is different.

Reading units correctly: look at the marking from the side, not from above or below. The bottom of the plunger tip is the reading. Parallax error (wrong angle) is a source of dosing error.

Insulin syringe graduations: U-100 syringes are marked in units where 100 units = 1 mL. Always confirm your syringe is U-100. Confusion between insulin units and milligrams is the most common syringe error.

Needle length: typical lengths for subcutaneous injection are 4-6 mm (short), 8 mm (standard), or 10-12 mm (longer). Longer needles are needed for deeper tissue or if you have abdominal adiposity.

Fixed versus detachable needles: insulin syringes usually have fixed needles (no dead volume loss to the hub). Luer-lock syringes use detachable needles (more dead volume). Fixed needles are preferred for small doses.